All-Glass Revolving Door Slim Framed Revolving Door Crystal Revolving Door
The All-Glass Revolving Door are completely constructed from glass with only the most minimal stainless steel frame and cappings, also known as Crystal Door, is the most transparent revolving door. Despite its transparency, it makes a striking entry to any building. It is available with three or four door wings with motorized operation.
The Crystal revolving door can be finished in completely clear glass, but colored glass is also available. With a variety of options available, we can work with you to ensure the Crystal door meets all your requirements.
Full glass revolving door
Structural Design
Frame construction: All glass.
Curved walls: 8mm+1.52+8mm laminated hot bent glass.
Canopy: 8mm+1.52+8mm laminated tempered glass.
Door leaves: 12mm flat tempered glass.
Other accessories: stainless steel connectors.
Features:
All drives and controls are hidden underground
Aluminum alloy profile, round side angle, elegant shape design
Low torque drive unit with Speed Control
Collapsible door set
Push-button temporary low speed
Power assist, Positioning Speed Control for optional manual doors
Push & Go or motion detection start up
Idle speed
Direction sensitive motion detectors
Stainless steel soffit
Colored interlayer to glass soffit,
Curved walls and night locking doors
Roof trim
Floor mats
Remote monitoring software
Night Locking Options
Specification
| Operation mode |
Manual |
Push&Go |
Automatic |
All-Glass |
| Canopy height (mm) |
72 |
200 |
200/75 |
17/ 25 |
Inside diameter
(mm) |
1800~3000
(maximal 3600) |
1800~3600 |
1800~3600 |
1800~3300 |
Clear height
(mm) |
<=3000 |
<=3000 |
<=3000 |
<=2600 |
| Door leaves |
3/4 |
3/4 |
3/4 |
3/4 |
| Inside diameter |
Outside diameter |
Entrance width
3 wing |
Entrance width
4 wing |
| 1800mm |
1850mm |
875mm |
1258mm |
| 2000mm |
2050mm |
975mm |
1399mm |
| 2200mm |
2250mm |
1075mm |
1540mm |
| 2400mm |
2450mm |
1175mm |
1681mm |
| 2600mm |
2650mm |
1275mm |
1822mm |
| 2800mm |
2850mm |
1375mm |
1963mm |
| 3000mm |
3050mm |
1475mm |
2104mm |
Slim framed revolving door
Security system
* Anti-strike sensor (with airbag type sensor)
Sensors are installed at the bottom edge of each door wing. When the rubber strip is squeezed, the door wing will stop revolving immediately to prevent the door wing from hitting pedestrians or objects.
* Anti-squeeze sensor
There is a hidden sensor inside the rubber strip on the right side of the entrance. In case of contact or compression, the door shall stop turning immediately to prevent pedestrians from being injured. The revolving door will return to normal as soon as the obstacle cleared.
* Handicap button installed on the entrance control panel bracket, once pressed, the speed is 1/3 of the normal speed.
* Emergency stop button once pressed and the revolving door will stop.
Drive and control system
* The revolving door system using three-phase motor, including a small PLC controller and a frequency controller, can provide a number of adjustable control functions.
* Computer controlled automatic system, using infrared motion sensor. If the sensor is activated, the door immediately turns 180 degrees at its normal speed. Due to the frequency controller, the speed of the door can be adjusted (0-9 rounds per minute). If the door is pulled by hand, the control system will stop automatically and running again after receiving a start signal.
Doors will stop immediately in the following cases:
The rubber inductor on the right side of the gatepost is squeezed;
The emergency stop button pressed;
In case of power failure, the door can be manual pushed.
Packing and delivery
Company Introduction
As manufacturing factory headquartered in guangzhou, an important port city of China's foreign trade, Guangzhou CN Electrical Equipment Co., Ltd. is a high-tech enterprise which integrating R&D, Manufacturing and Trading, one of the leading and exclusive manufacturer of Automatic Partitions and Automatic Doors and the only company in China which has a dedicated manufacturing plant of electrically operated vertical lift folding partition Walls in China.
Our factory covers an area of more than 12,000 square meters. We have our products installations throughout china and abroad. The annual manufacturing capacity to 500 sets of various automatic revolving doors and 10,000 square meters of motorized partition walls, we have produced and installed Automatic Doors and Electrical Movable Walls for all types of establishments like high end residences / conference room / banquet halls in hotels / auditorium / convention centre / meeting rooms / board rooms / training rooms etc.
All the materials used are in compliance to international standards such as ISO 9001, CE, IEC etc. With the strictly control for designed, production, inspection and services by our advanced quality management system, enable the products of Guangzhou CN Electrical Device Co., Ltd selling well in the domestic market, and keep rapid growth in the European, American, Asia and Middle East market. Successfully established strategic cooperative partnership with famous domestic and foreign enterprises like Siemens, Phillips, and BEA etc.
Factory Details
Our factory is equipped with state of the art hydraulic press brake bending machines, automatic cutting machines for cutting aluminium and MDF boards and complete equipment like drilling, milling, bearing and lamination press machines, processing and manufacturing any type of doors and movable walls as per customer choice.
FAQs
Q: Are you trading company or manufacturer?
A: We are automatic door manufacturer for many years.
Q: How long is your delivery time?
A: Standard products within 10-15 days after received 50% deposit. Customized products depend on agreement.
Q: Do you provide samples ? is it free or extra?
A: Free samples can only be provided if the order is large enough. A small quantity can only be a trial order.
Q: What is your terms of payment?
A: 30% -50%deposit and balance before shipment, T/T, Western Union or Cash accepted.
){kind=link}